8 Channel RF Remote Receiver with Holtek and Serial Protocol

  • Rajkumar Sharma
  • 233 Views
  • easy
  • Tested
  • SKU: EL135662
  • Quote Now

The project described here is 8 Channel RF Remote Receiver (Decoder). This 8-channel decoder is built using LICAL-EDC-DS001 chip from LINX. The board consists of the encoder/Decoder chip, 433Mhz RF Receiver module, and 10 x jumpers to set the address. Also, there is a header connector for data output which is ideal for controlling external devices, for example, relays. All outputs are compatible with TTL logic, normally they are low and go high when a valid signal is received and decoded by the chip. D2 onboard Power LED, D1 LED indicates valid transmission signal. All outputs are momentary (not latching)

 Features

  • Supply 5V DC
  • 10 Address Lines Selected through Jumpers J1 to J10
  • 8 Data Output TTL Compatible Normally Low (Momentary)
  • On Board Power LED
  • On Board VT LED (Valid Transmission)
  • PCB Dimensions 45.09 x 33.02 mm
  • 2 x 2.5mm Mounting Holes

System Configuration

A simple remote-control system consists of an encoder, an RF transmitter, an RF receiver, and a decoder. The encoder is connected to 8 buttons, The encoder detects the closure of one of the switches and converts that into a digital data stream. This data is then sent to an RF transmitter that conveys this data into free space. An RF receiver receives the data and sends it to a decoder. The decoder analyses the data and, if it is valid, replicates the switch closure on an output. This output is then connected to whatever circuitry is to be controlled. All outputs are momentary and TTL logic.

remote control system (transmitter and receiver)

This DS series decoder and encoder chip is ideal for remote control applications. It decodes the signal received by 433 MHz RF modules. When the DS enters Decoder Mode, it checks the state of the DIN line. If it is high, the P_SEL line is checked to set which protocol is used and the decoder receives the data. It compares the address in the received packet to its local address lines. If they match, the data is stored and a second packet is received. With the Holtek® protocol, the decoder compares the two packets. If they match, the received data bits are output on the data lines and the VT line is pulled high thus LED D1 is on. This protocol compares each packet with the previous one looking for a match. The serial protocol requires two matching packets for initial activation, then updates the lines on each subsequent packet. The DS then looks for the next packet on the DIN line. With the Holtek® protocol, once no valid data is received (there is a mismatch of address, data, or bit timings), the Data and VT lines are pulled low and the DS goes to sleep until DIN is pulled high. The Serial protocol holds the output states until a 130ms timer runs out. The Holtek® protocol compares two packets and, if they match, sets the outputs. If a data line is toggled during a transmission (D1 is activated while D0 is already active) then the received packet does not match the previous packet and the output lines are pulled low until the next packet arrives. This causes all of the outputs to briefly cut out when a line is toggled. The serial protocol uses a timer to prevent this cutout.

LICAL-EDC-DS001 Encoder/Decoder Chip

The same part can be used as an encoder or decoder by selecting the state of one pin. The DS Series also has two protocols built into the same part, selected by the state of a single pin. One is compatible with Holtek devices, such as the HT640 and HT658. The other protocol is a serial data structure that is much more immune to noise and edge jitter. This protocol offers much more range and reliability than the Holtek protocol while keeping the simple jumper addressing.

Theory of Operation

The DS Series is a remote-control encoder and decoder that offers two protocols in one part based on the state of the P_SEL line. The first protocol operates with the Holtek® HT640 encoder and HT658 decoder. The second is a serial protocol that offers more noise immunity and faster response time while keeping the simple addressing. The DS can operate as either an encoder or decoder based on the state of the E/D_SEL line. It does not operate as both simultaneously. When set as an encoder it monitors the state of the TE line. When the line is high the DS records the states of the data and address lines, assembles them into a packet, and outputs the packet three times. The data lines can be connected to switches or contacts. The address lines can be set with Jumpers. When set as a decoder the DS receives packets and validates them. The validation includes checking the bit timings and comparing the received address to the local address line settings. Two matching packets must be received consecutively. If the timings are good and the addresses match, the DS sets its data lines to match the received states. These lines can be connected to the application circuitry to be controlled. When the TE/DIN line is low, the DS goes into a low-power sleep mode.

Setting the Address

The project has ten address lines. This allows the formation of up to 1,022 (210 – 2) unique transmitter-receiver relationships, Jumper J1 to J10 can be used to set the address, all lines are pulled high. The chip rejects packets with addresses set to all high or all low. At least one address line must be different from the rest. The encoder does transmit all addresses, but the decoder rejects packets with all address lines set the same. The receiver’s address line states must match the transmitter’s exactly for a transmission to be recognized. If the addresses do not match, then the decoder takes no action.

Initial Operation

On power-up, the E/D_SEL line is tested to determine if the DS operates as an encoder or a decoder. If the line is high, the DS enters Encoder Mode. If low, it enters Decoder Mode. This is checked once on power-up. Once the operating mode is selected, the data-line direction is set. In either mode, a rising edge on the TE/DIN line wakes the device from low-power sleep.

Connections and Other Information

  • Connections and Other Details
  • CN1: Pin 1 = VCC 5V In, Pin 2 = D0, Pin 3 = D1, Pin 4 = D2, Pin 5 = D3, Pin 6 = D4, Pin 7 = D5, Pin 8 = D6, Pin 9 = D7, Pin 10 GND
  • D1: Valid Signal LED
  • D2: Power LED
  • Jumper: J1 to J10 for Address Configuration
  • For Serial Protocol R2 = 0 Ohms, R3 Omit, For Holtek Protocol R3= 0 Ohms and R2 Omit (Read Data sheet of chip for Serial/Holtek Protocol)

Schematic

Parts List

NOQNTY.REFDESCMANUFACTURERSUPPLIERSUPPLIER PART NO
11CN18 PIN MALE HEADER PITCH 2.54MMWURTHDIGIKEY732-5321-ND
21C1100nF/25V CERAMIC SMD SIZE 0805MUARATA/YAGEODIGIKEY
31C210uF/16V CERAMIC SMD SIZE 1206MUARATA/YAGEODIGIKEY
41D1LED -GREEN SMD SIZE 0805DIALIGHTDIGIKEY350-2044-1-ND
51D2LED RED SMD SIZE 0805OSRAMDIGIKEY475-1278-1-ND
61E1ANTENNA/DNPDO NOT INSTALL
710J1-J10JUMPER/ 2 PIN MALE HEADER PITCH 2.54MMWURTHDIGIKEY732-5315
81M1RF AM RX MODULE 433MHZ.ALIEXPRESSALIEXPRESS
92R1,R141K/5% SMD SIZE 0805MUARATA/YAGEODIGIKEY
101R2DNP
111R30E SMD SIZE 0805MUARATA/YAGEODIGIKEY
1210R4-R13100K/5% SMD SIZE 0805MUARATA/YAGEODIGIKEY
131U1LICAL-EDC-DS001-TLINX TECHDIGIKEYLICAL-EDC-DS001-TCT-ND
1410SHUNTSHUNT FOR JUMPER J1 TO J10SULLINS CONNCTDIGIKEYS9001-ND

Connections

 

Gerber View

Photos

Video


LICAL-EDC-DS001 Datasheet

Please follow and like us:
Pin Share

PCB



Subscribe
Notify of
guest

0 Comments
Inline Feedbacks
View all comments

RELATED PROJECTS

TOP PCB Companies